Skip to product information
1 of 1

BuildYourCNC

1/4" Cut Diameter Single Flute End Mill for Plastic and Wood Cutting

1/4" Cut Diameter Single Flute End Mill for Plastic and Wood Cutting

Regular price $29.85 USD
Regular price Sale price $29.85 USD
Sale Sold out
Title
These have a single flute with a deep cavity to carry a lot of material out of the cut. It's like digging with a shovel that can hold much more dirt. These end mills are designed mainly for plastic but will work with wood and it is surprisingly more quiet than the two flute end mills. This end mill will create a flat bottom surface
Technical Specifications: Cut Diameter: 1/4 inch (6.35mm) Shank Diameter: 1/4 inch (6.35mm) Cut Length: 1/2" (13mm) and 1" (25mm) Overall Length: 2" (50mm)
View full details

Questions & Answers

Have a Question?

Ask a Question
  • I AM TAKING THE FINAL YEAR PROJECT IN BASE STATIONS AND AIR INTERFACE. WOULD LIKE TO HAVE SOME INFORMATION.

    The Federal Communications Commission (FCC) is the primary federal agency responsible for safety aspects of modern-day wireless telecommunications systems. The FCC's Internet address is shown below. Recently FCC published an excellent report, cited below, to assist citizens and local governments dealing with siting of telecommuncations towers. This report contains charts and figures describing the characteristics and performance of telecommunications antennas. The report also contains practical guidance on application of provisions of the Telecommunications Act of 1996, which is the governing legislation regarding safety and siting of wireless telelcommunications facilities. Web page: RF Safety Program Page. Report title: "A Local Government Official's Guide to Transmitting Antenna RF Emission Safety: Rules, Procedures, and Practical Guidance." The Local and State Government Advisory Committee (LSGAC) and the FCC have developed this guide to aid local governmental officials and citizens in understanding safety issues related to radiofrequency emissions from telecommunications towers. Gary Zeman, Sc.D., CHP Lawrence Berkeley National Laboratory

  • HAVE THERE BEEN ANY STUDIES OF POSSIBLE RADIATION DANGER FROM HEADSETS USED WITH HANDSETS CORDED TELEPHONES? I A TELEPHONE BATTERY-POWERED HANDSET. THIS HANDSET HAS JACK FOR HEADSET, SO YOU CAN WALK AROUND THE HOUSE AND YARD ON YOUR BELT WHILE TALK INTO HEADSET. EITHER OR HEADSET GIVING OFF RADIATION, LIKE CELLULAR PHONE? DANGEROUS AMOUNT RADIATION?

    Headsets have been tested by the manufacturers and meet the current ANSI/IEEE standards for RF safety, the same standards that the Federal Communications Commission enforces under the Telecommunications Act of 1996. These standards place limits on the specific absorption rate (SAR) of radiofrequency (RF) energy in the body. Recent inflamatory articles in British press were not substantiated by testing in ISO-accredited testing facilities at Motorola. Manufacturers of cellular phones are required under FCC regulations to assure that their products meet the SAR limits on both hand-held and hands-free units. Further information may be available from the FDA or from the FCC. Ron Petersen, Lucent C.K. Chou, Motorola

  • COULD YOU PLEASE EXPLAIN, IF IT'S TRUE, THAT HANDS-FREE CELL PHONE CAR MICROPHONES RADIATE MORE THAN ANY OTHER INSTRUMENT USED WITH THESE PHONES?

    Hands-free cell phone car microphones have been tested by the manufacturers and meet the current ANSI/IEEE (American National Standards Institute/Institute of Electrical and Electronics Engineers) standards for radiofrequency (RF) safety. These are the same standards that the Federal Communications Commission enforces under the Telecommunications Act of 1996, and they place limits on the specific absorption rate (SAR) of RF energy in the body. Recent inflammatory articles in the British press were not substantiated by testing at ISO-accredited testing facilities at Motorola. Manufacturers of cell phones are required under FCC regulations to assure that their products meet the SAR limits on both hand-held and hands-free units. Further information can be obtained on the Internet at The Center for Devices and Radiological Health (FDA information) or Office of Engineering and Technology (FCC information).