[ Log In ]
Newbie Hack Shirt Back
The STM32 ultra basic kit showing all of the components

STM32 Ultra Basic Kit Special Introductory Price!

$34.95
Qty:
ST Link v2 for STM32 and STM8 microcontrollers top view of all components

ST-Link v2 STM32 and STM8 Programmer

$9.95
Qty:
STM32F0 microcontroller and interface board top view

STM32 M0 MCU and Interface to Breadboard

$14.95
Qty:
Image of the Atmega324p

Atmega324P

$8.50
Qty:
Serial to USB converter with Micro USB cable

USB to Serial Converter

$10.95
Qty:
Thumbnail: Crystal Oscillator 18.432 MHz for UART

18.432 MHz Crystal Oscillator 18pf 30ppm

$0.94
Qty:
Thumbnail: 22 pF Capacitor

22 pF Multilayer Ceramic Capacitor

$0.43
Qty:
Thumbnail: Quartz crystal oscillator - 16 MHz

16 MHz Crystal Oscillator 20 pF Through Hole

$0.75
Qty:
Thumbnail: 4x4 keypad top view.

4x4 Keypad with Adhesive Backing

$3.80
Qty:

ARM Microcontroller Beginners Kit (STM32F0)

The ARM microcontroller beginners kit
The ARM microcontroller beginners kit

Introduction:

Start your journey into the ARM Microcontroller Development with this beginners kit based around the STM32F0 series. Includes all you need to get started!

Description:

Don't worry about needing the components necessary for getting into the ARM development world. This kit includes a bunch of components for you to start making circuits of all kinds.

The ARM microcontroller kit uses the STM32F030 microcontroller. You will be able to program the microcontroller with the included ST-LinkV2 interface programmer.

The STM32F030 is soldered onto a convenient breakout board that will fit nicely into the three included breadboards. The breakout board was designed specifically to use the three breadboard so that you can maximize the development possibilities. This allows each pin to have two separate tie strips which have a total of nine (9) points (4 for one tie strip and 5 for the other.

The kit includes the following components:

  • STM32F030 Microcontroller and breakout board
  • ST-LinkV2 Programmer
  • Cable to connect the ST-LinkV2
  • (3) Breadboards
  • Resistors: (4) 1k, (4) 10k, and (20) 330 ohm
  • (2) Push Buttons
  • (12) Green LEDs
  • (2) Red LEDs
  • Solid Core Jumper Set with 140 total hookup wires of different lengths and colors
  • (2) 10uF Electrolytic Capacitors
  • (2) 100uF Electrolytic Capacitors
  • (6) 100nF/0.1uF Capacitors

ARM Microcontroller Beginners Kit (STM32F0)

$39.95
Qty:

Learn about the ARM Microcontroller Beginners Kit (STM32F0)

Introduction and setup of Atmel Studio 6 IDE (Integrated Development Environment) for programming Atmel AVR and ARM microcontrollers.
Installation of Atmel Studio 6 IDE (Integrated Development Environment) for programming Atmel AVR and ARM microcontrollers.
Part 1: Walkthrough of the Atmel Studio 6 IDE (Integrated Development Environment) for programming Atmel AVR and ARM microcontrollers.
Part 2: Walkthrough of the Atmel Studio 6 IDE (Integrated Development Environment) for programming Atmel AVR and ARM microcontrollers.
Starting a new project and specifying the microcontroller: Atmel Studio 6 IDE (Integrated Development Environment) for programming Atmel AVR and ARM microcontrollers.